642-813J SWITCH 試験
Implementing Cisco IP Switched Networks

試験概要
Implementing Cisco IP Switched Networks (SWITCH 642-813) は、Cisco Certified Network Professional CCNP® および Cisco Certified Design Professional CCDP® 認定の取得に必要な試験です。 SWITCH 642-813 試験では、Cisco Enterprise Campus Architecture を使用して複雑なエンタープライズ スイッチング ソリューションの実装の際の計画、設定、検証に必要な重要な知識とスキルが問われます。この試験では、VLAN、WLAN、音声およびビデオをキャンパス ネットワークにセキュアに統合する方法もカバーされます。

進歩を勇敢に追及する人生こそ素晴らしい人生です。未来のある日、椅子で休むとき、自分の人生を思い出したときに笑顔が出たら成功な人生になります。あなたは成功な人生がほしいですか。そうしたいのなら、速くJapanCertのCiscoの642-813試験トレーニング資料を利用してください。これはIT認証試験を受ける皆さんのために特別に研究されたもので、１００パーセントの合格率を保証できますから、躊躇わずに購入しましょう。

642-813認定試験を受験したいですか。642-813認証資格を取得したいですか。試験に準備する時間が足りないあなたは、どうやって試験に合格できますか。しようがないわけではないです。短時間の準備でも楽に試験に合格することができるようになりますよ。それでは、どのようにすればそれを達成できますか。実は方法がとても簡単です。すなわちJapanCertの642-813問題集を利用して試験の準備をすることです。

君はまだCisco 642-813認証試験を通じての大きい難度が悩んでいますか？ 君はまだCisco 642-813認証試験に合格するために寝食を忘れて頑張って復習しますか？ 早くてCisco 642-813認証試験を通りたいですか？JapanCertを選択しましょう！JapanCertはきみのIT夢に向かって力になりますよ。

642-813認定試験はずっと人気があるのです。最近IT試験を受けて認証資格を取ることは一層重要になりました。たとえばCisco、IBM、Cisco、VMware、SAPなどのいろいろな試験は今では全部非常に重要な試験です。より多くの人々は複数の資格を取得するために多くの642-813試験を受験したいと思っています。もちろん、このようにすればあなたがすごい技能を身につけていることが証明されることができます。しかし、仕事しながら試験の準備をすることはもともと大変で、複数の試験を受験すれば非常に多くの時間が必要です。いまこのようなことで悩んいるのでしょうか。それは問題ではないですよ。JapanCertあなたを時間を節約させことができますから。JapanCertのさまざまなIT試験の問題集はあなたを受験したい任意の試験に合格させることができます。642-813認定試験などの様々な認定試験で、受験したいなら躊躇わずに申し込んでください。心配する必要はないです。

JapanCertの問題集を買ったら1年間の無料オンラインのアップデートを提供する一方で、試験に失敗したら、お客様に全額で返金いたします。

JapanCertが提供する真実と全面的なCisco認証試験について資料で100%で君の試験に合格させてまたあなたに1年無料のサービスを更新し、今はJapanCertのインターネットで無料のCiscoの642-813認証試験問題集のソフトウェアがダウンロード することができます。

購入前にお試し,私たちの試験の質問と回答のいずれかの無料サンプルをダウンロード：http://www.japancert.com/642-813.html

NO.1 Refer to the exhibit.
Which statement about the private VLAN configuration is true?
A. Only VLAN 503 will be the community PVLAN, because multiple community PVLANs are not
allowed.
B. Users of VLANs 501 and 503 will be able to communicate.
C. VLAN 502 is a secondary VLAN.
D. VLAN 502 will be a standalone VLAN, because it is not associated with any other VLANs.
Answer: C

Cisco 642-813勉強法 642-813特典 642-813リンクグローバル 642-813試験感想
Explanation:
VLAN 502 has been configured as private-vlan community. So it is a secondary PVLAN

NO.2 By default, all VLANs will belong to which MST instance when using Multiple STP?
A. MST00
B. MST01
C. The last MST instance configured
D. None
Answer: A

Cisco模試エンジン 642-813科目対策 642-813 642-813解答例 642-813ファンデーション
Explanation:
Recall that the whole idea behind MST is the capability to map multiple VLANs to a smaller number of
STP instances. Inside a region, the actual MST instances (MSTIs) exist alongside the IST. Cisco
supports a maximum of 16 MSTIs in each region. IST always exists as MSTI number 0, leaving MSTI 1
through 15 available for use. By default all VLANs are belonged to MST00 instance.

NO.3 CORRECT TEXT
Each of these vlans has one host each on its ports
SVI on vlan 1 - ip 192.168.1.11 Switch B -Ports 3, 4 connected to ports 3 and 4 on Switch A
Port 15 connected to Port on Router.
Tasks to do:
1.Use non proprietary mode of aggregation with Switch B being the initiator -- Use LACP with B being
in Active mode
2.Use non proprietary trunking and no negotiation -- Use switchport mode trunk and switchport trunk
encapsulation dot1q
3.Restrict only to the VLANs needed -- Use either VTP pruning or allowed VLAN list. The preferred
method is using allowed VLAN list
4.SVI on VLAN 1 with some ip and subnet given
5.Configure switch A so that nodes other side of Router C are accessible -- on switch A the default
gateway has to be configured.
6.Make switch B the root
Answer:
on Switch A
verify with show run if you need to create vlans 21-23
int range fa0/9 - 10
switchport mode access
switchport access vlan 21
spanning-tree portfast
no shut
int range fa0/13 - 14
switchport mode access
switchport access vlan 22
spanning-tree portfast
no shut
int range fa0/16 - 16
switchport mode access
switchport access vlan 23
spanning-tree portfast
no shut
int range fa0/3 - 4
channel-protocol lacp
channel group 1 mode passive
no shut
int port-channel 1
switchport mode trunk
switchport trunk encapsulation dot1q
spanning-tree allowed vlans 1,21-23
no shut
int vlan 1
ip address 192.168.1.11 255.255.255.0
no shut
SW B
conf t
interface range fastethernet 0/9-10
switchport mode access
switchport accress vlan 21
spanning-tree portfast
no shut
interface rang fastethernet 0/13-14
switchport mode access
switchport accress vlan 22
spanning-tree portfast
no shut
interface rang fastethernet 0/15-16
switchport mode access
switchport accress vlan 23
spanning-tree portfast
no shut
interface range fastethernet 0/3-4
switchport trunk encapsulation dot1q
switchport trunk native vlan 99
switchport trunk allowed vlan 1,21-23,99
switchport mode trunk
channel-protocol lacp
channel-group 1 mode passsive
no shut
// port-channel 1 automatically created and nothing needs to be configured under it
ip default-gateway 10.10.10.1
// VLAN 1 already configured nothing more to be done on it
SWA
vlan 21
vlan 22
vlan 23
interface range fastethernet 0/3-4
switchport trunk native vlan 99
switchport trunk allowed vlan 1,21-23,99
switchport mode trunk
channel-protocol lacp
channel-group 1 mode active
no shut
spanning-tree vlan 1,21-23,99 root primary

NO.4 Refer to the exhibit.
From the configuration shown, what can be determined?
A. The sticky addresses are only those manually configured MAC addresses enabled with the sticky
keyword.
B. The remaining secure MAC addresses are learned dynamically, converted to sticky secure MAC
addresses, and added to the running configuration.
C. A voice VLAN is configured in this example, so port security should be set for a maximum of 2.
D. A security violation restricts the number of addresses to a maximum of 10 addresses per access
VLAN and voice VLAN. The port is shut down if more than 10 devices per VLAN attempt to access the
port.
Answer: B

Cisco 642-813番号 642-813模試エンジン 642-813
Explanation:
By enabling sticky port security, you can configure an interface to convert the dynamic MAC
addresses to sticky secure MAC addresses and to add them to the running configuration. You might
want to do this if you do not expect the user to move to another port, and you want to avoid
statically configuring a MAC address on every port. To enable sticky port security, enter the
switchport port-security mac-address sticky command. When you enter this command, the interface
converts all the dynamic secure MAC addresses, including those that were dynamically learned
before sticky learning was enabled, to sticky secure MAC addresses. The sticky secure MAC addresses
do not automatically become part of the configuration file, which is the startup configuration used
each time the switch restarts. If you save the running config file to the configuration file, the interface
does not need to relearn these addresses when the switch restarts. If you do not save the
configuration, they are lost.
Reference:
http://www.cisco.com/en/US/docs/switches/lan/catalyst4500/12.2/53SG/configuration/port_sec.ht
m l#wp1047668

NO.5 HOTSPOT
Answer:
Explanation:
Enable preempt on the VLAN 101 HSRP group on DSW1 Issue the "show run" command and you can
see that the "standby 1 preempt" configuration command is missing on DSW1. This is needed for it to
become the active HSRP router immediately.

NO.6 Refer to the exhibit.
HSRP has been configured and Link A is the primary route to router R4. When Link A fails, router R2
(Link B) becomes the active router. Which router will assume the active role when Link A becomes
operational again?
A. The primary router R1 will reassume the active role when it comes back online.
B. The standby router R2 will remain active and will forward the active role to router R1 only in the
event of its own failure.
C. The standby router R2 will remain active and will forward the active role to router R1 only in the
event of Link B failure.
D. The third member of the HSRP group, router R3, will take over the active role only in event of
router R2 failure.
Answer: A

Cisco試験問題集 642-813最新版 642-813通信 642-813 642-813
Explanation:
When Link A goes down, the HSRP priority value of R1 goes down to 95 (105-10) so R2 will be the
active router as it is using the default priority of 100. When Link A comes back up, R1's priority is then
105 again and since pre-emption is enabled, it will take back over the active role again.

NO.7 Which three items are configured in MST configuration submode? (Select three)
A. Region name
B. Configuration revision number
C. VLAN instance map
D. IST STP BPDU hello timer
E. CST instance map
F. PVST+ instance map
Answer: A,B,C

Cisco 642-813教科書 642-813認証試験
Explanation:
spanning-tree mst configuration:
Use the spanning-tree mst configuration command to enter the MST configuration submode. Use
the no form of this command to return to the default MST configuration.
Defaults:
The default value for the MST configuration is the default value for all its parameters:
Usage Guidelines:
The MST configuration consists of three main parameters:

NO.8 What is needed to verify that a newly implemented security solution is performing as expected
?
A. a detailed physical and logical topology
B. a cost analysis of the implemented solution
C. detailed logs from the AAA and SNMP servers
D. results from audit testing of the implemented solution
Answer: D

Cisco 642-813指導 642-813サンプル問題集 642-813好評
Explanation:
Recommended by Cisco verification plan for designing a security solution includes verification of an
implemented security solution requires results from audit testing of the implemented solution.
Reference:
http://www.ccnpguide.com/design-documentation/

JapanCertは最新のM2140-726問題集と高品質の1Y0-350問題と回答を提供します。JapanCertのSPHR VCEテストエンジンとC4040-120試験ガイドはあなたが一回で試験に合格するのを助けることができます。高品質のH13-622 PDFトレーニング教材は、あなたがより迅速かつ簡単に試験に合格することを100％保証します。試験に合格して認証資格を取るのはそのような簡単なことです。

記事のリンク：http://www.japancert.com/642-813.html