近年、Ciscoの640-802 認定試験はIT能力認定試験としてますます重要になっています。

640-802 Cisco Certified Network Associate（CCNA）は、Cisco Certified Network Associate 認定資格に関連した複合試験です。受験者は、受験準備として Interconnecting Cisco Networking Devices Part 1（ICND1） v1.0コースおよび Cisco Networking Devices Part 2（ICND2）v1.0コースを受講できます。この試験では、WAN への接続およびネットワーク セキュリティの実装を含め、小規模ネットワークの導入、運用、およびトラブルシューティングを行うための知識が問われます。

どうでしょう。あなたはこの試験に合格する信心を持っていますか。試験に合格する自信を持っていない人はこちらへご覧ください。Japancertが提供したCiscoの640-802試験に関する最高の問題集をささげます。これは特に試験に受かる自信を持たないあなたのために準備するものです。これはIT専門家達が試験に要求された要件に満たせない受験生を対象として特別に作成された問題集ですから、ぜひあなたがCiscoの640-802認証試験に受かることを保証できます。不思議だと思いますか。そうしたら、体験してみてください。無料な試用版もありますよ。

JapancertのCiscoの640-802問題集 は IT専門家達が受験生の皆さんの需要にこたえて特別に研究された成果です。一度利用したらその便宜をよく知られるようになります。あなたの一発合格のことを保証できますから、ぜひ問題集を手に入れてください。

JapancertのCiscoの640-802問題集は最近更新したものですから、安心にご利用ください。

試験番号：640-802
試験科目：Cisco（Cisco Certified Network Associate(CCNA)）
問題数：653

無料な問題集のサンプルを利用することができますよ。http://www.japancert.com/640-802.html

NO.1 Which command is used to configure a default route?
A. ip route 172.16.1.0 255.255.255.0 0.0.0.0
B. ip route 172.16.1.0 255.255.255.0 172.16.2.1
C. ip route 0.0.0.0 255.255.255.0 172.16.2.1
D. ip route 0.0.0.0 0.0.0.0 172.16.2.1
Answer: D

NO.2 Which two addresses can be assigned to a host with a subnet mask of 255.255.254.0? (Choose two.)
A. 113.10.4.0
B. 186.54.3.0
C. 175.33.3.255
D. 26.35.2.255
E. 17.35.36.0
Answer: BD

NO.3 Which command reveals the last method used to powercycle a router?
A. show reload
B. show boot
C. show running-config
D. show version
Answer: D

NO.4 Which command would you configure globally on a Cisco router that would allow you to view directly
connected Cisco devices?
A. enable cdp
B. cdp enable
C. cdp run
D. run cdp
Answer: C

NO.5 Which command is used to see the path taken by packets across an IP network?
A. show ip route
B. show route
C. traceroute
D. trace ip route
Answer: C

NO.6 Which protocols are found in the network layer of the OSI reference model and are responsible for
path determination and traffic switching?
A. LAN
B. routing
C. WAN
D. network
Answer: B

NO.7 If IP routing is enabled, which two commands set the gateway of last resort to the default gateway?
(Choose two.)
A. ip default-gateway 0.0.0.0
B. ip route 172.16.2.1 0.0.0.0 0.0.0.0
C. ip default-network 0.0.0.0
D. ip default-route 0.0.0.0 0.0.0.0 172.16.2.1
E. ip route 0.0.0.0 0.0.0.0 172.16.2.1
Answer: CE

NO.8 Which three options are valid WAN connectivity methods? (Choose three.)
A. PPP
B. WAP
C. HDLC
D. MPLS
E. L2TPv3
F. ATM
Answer: ACF

NO.9 Workstation A has been assigned an IP address of 192.0.2.24/28. Workstation B has been assigned an
IP address of 192.0.2.100/28. The two workstations are connected with a straight-through cable. Attempts
to ping between the hosts are unsuccessful. What two things can be done to allow communications
between the hosts? (Choose two.)
A. Replace the straight-through cable with a crossover cable.
B. Change the subnet mask of the hosts to /25.
C. Change the subnet mask of the hosts to /26.
D. Change the address of Workstation A to 192.0.2.15.
E. Change the address of Workstation B to 192.0.2.111.
Answer: AB

NO.10 Refer to the exhibit.
Which WAN protocol is being used?
A. ATM
B. HDLC
C. Frame Relay
D. PPP
Answer: C

NO.11 Which command is used to debug a ping command?
A. debug icmp
B. debug ip icmp
C. debug tcp
D. debug packet
Answer: B

NO.12 Which command displays CPU utilization?
A. show protocols
B. show process
C. show system
D. show version
Answer: B

NO.13 Which command shows system hardware and software version information?
A. show configuration
B. show environment
C. show inventory
D. show platform
E. show version
Answer: E

NO.14 Cisco Catalyst switches CAT1 and CAT2 have a connection between them using ports FA0/13. An 802.
1Q trunk is configured between the two switches. On CAT1, VLAN 10 is chosen as native, but on CAT2
the native VLAN is not specified.What will happen in this scenario?
A. 802.1Q giants frames could saturate the link.
B. VLAN 10 on CAT1 and VLAN 1 on CAT2 will send untagged frames.
C. A native VLAN mismatch error message will appear.
D. VLAN 10 on CAT1 and VLAN 1 on CAT2 will send tagged frames.
Answer: C

NO.15 Data transfer is slow between the source and destination. The quality of service requested by the
transport layer in the OSI reference model is not being maintained. To fix this issue, at which layer should
the troubleshooting process begin?
A. presentation
B. session
C. transport
D. network
E. physical
Answer: D

640-802最新の問題集